Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to auto locksmiths with experience who have the right equipment and technical knowledge. They can create and program new keys faster than a dealership would and at a lower price.

If the key fob has stopped locking or unlocking your doors it is likely due to a dead battery in the coin. However, Peugeot 208 Key Replacement there are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and will not start the engine. In this case you'll need use the alternative starting method as described in your vehicle's owner's manual.

The spark plugs may also be worn out. The spark plugs light the fuel to start the engine. However they have a finite lifespan. If they aren't used enough, they will eventually fail.

There is a simple solution for this problem. Check the voltage of your battery with a multimeter. If it's less than 11.5 volts then you must replace it. It is also essential to clean the battery's contacts in case it is corroded. This can be done by lifting the rubber covers that protect the two battery terminals and using a wire brush to remove any parts that are corroded from the battery. It is then time to reconnect your cables to connect the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery is not flat, then you need to make sure whether the spark plugs are working. It is possible that they're dirty, causing them not to spark. The spark plugs can be cleaned in an workshop.

Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This makes sure that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the correct signal to the vehicle.

This is a typical issue that can occur due to water damage. This is a typical issue in colder climates where the vehicle has been exposed to snow or rain. In this case, you need to contact a reputable locksmith who has the tools and equipment required to reprogram the key. They will also have the most up-to-date technological know-how and machinery required to make a Peugeot 208 smart key. The process should take no more than 15 minutes.

Faulty battery contacts

Peugeot replaced the transponder chips by introducing a new model that utilizes electronic components that are mounted on a circuit board. The new system is effective when it's new, but over time the circuit boards begin to degrade and stop working correctly.

This could prevent the immobiliser chip activating and causing your car to not start. If this happens, it's best to call a peugeot car key replacement specialist or locksmith.

A common issue is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith from your car will replace the battery, and then cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. The chip can be damaged by water in the event that it is exposed water for long periods of time. Submerging the key fob into the ocean at the beach or throwing it into the pool can be especially damaging because of the high salt content.

The module will need to be replaced if the peugeot car key spare key isn't working anymore. This can only be done by an Peugeot specialist or expert auto locksmith. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to begin the engine. It is for this reason that you should only trust a Peugeot locksmith to design and program an alternative.

Computer on-board is not working properly

The computer on board in your Peugeot is the one responsible for all of the systems in your car, ranging from power windows to airbags. When something goes wrong with these systems, they will usually show a code that identifies the problem. This code will be saved within the system until the problem is fixed. This may require the on-board computers to be replaced.

The most typical reason for the warning light of the airbag to come on is corroded or loose connections within the sensor. This can be caused by wear and tear, aging, exposure to moisture and salt. It is essential to have this issue addressed as soon as possible, as a malfunctioning airbag can be dangerous in the event an accident.

If your Peugeot is showing a card detected as not present error then the key battery inside the key fob might be weak or dead. This will stop the key fob sending a signal that will disable the immobilizer on your vehicle. Test this by pressing the unlock button on the key fob, and then trying to start your vehicle. If it doesn't work then the battery in the key fob is in need of replacement.